A marine water heater is simply a small, insulated tank downstream of the pump. You must have a pressurized water system to operate a water heater. The pump draws water from the storage tank(s) and fills the water heater tank. Inside the water heater is an electrical heating element and usually a coiled tube called a heat exchanger. When AC power is available, the electrical element (controlled by a thermostat) heats the water. Away from the dock, the hot engine coolant is routed through the coiled tube to heat the water in the tank when the engine is running.
Water heaters have four threaded ports. The tank inlet connects via a tee connector to the outlet hose from the pump. A check valve is required in this line or in the heater to prevent hot water from migrating back toward the pump. The outlet connection supplies heated water to the hot side of all faucets, also using tee connectors. The other two ports are for the heat exchanger connection, which varies depending on engine installation. Use only metal fittings to plumb a water heater, never plastic. If a pressure-release valve isn’t integral, the heater will have a fifth port for this essential component.
Raritan’s 1700 Series Water Heaters are built for the long haul. A glass-lined steel tank and a rust-proof jacket keep the Raritan water heater looking great and lasting for many years. Research has shown that glass-lined steel tanks are more durable than tanks made from just stainless steel. To increase longevity and fluctuations in water quality, Raritan includes a sacrificial magnesium anode that ensures a long tank life.
Features:
A heat exchanger (the heat exchanger allows the user to heat water when underway by circulating engine cooling fluid through the almost 7-foot-long coil within the tank)
The recovery rate can be as high as 18 gallons per hour
High-density non-CFC foam insulation helps the tank to maintain the hot water longer, a plus if you don’t want to run the generator for hot water
Hot water at 160 degrees F when mixed with cold water can greatly extend the usable capacity of the tank
Because the heater includes an adjustable thermostat it can be set as high as 160 degrees F
All plumbing connections on one side (it retrofits without difficulty to most onboard pressure systems)
Hot and cold-water fittings are standard 3/4 in. male NPT and the heat exchanger’s 3/4 in. female NPT
Specifications:
Tank Size: 20-gallon
Volts: 240
Benefits:
Simple installation – retrofits to most on-board pressure systems
Proven long-life design
Withstands the rigors of the marine environment
The glass-lined steel tank is more durable than stainless steel
The attractive polymer jacket resists corrosion from dampness
Ignition-protected, adjustable thermostat
Round tanks are designed to withstand more pressure than square tanks
Glass-lined steel tank for long life and high efficiency
Environmentally friendly CFC-free foam insulation
Replaceable magnesium anode to protect the tank and neutralize acids in the water
The tank is covered by a five-year Limited Warranty
Each unit is assembled by hand, individually tested, and backed by Raritan’s two-year Limited Warranty and legendary technical support team
I've started using the mulcher I on several parcels of land 10 acres . I have grind down a couple of 14 inch stumps. Caution the mount bracket behind the mulcher motor exhaust gets extremely hot even with gloves on . But the unit so far seems to works very good it's well put together.
The Firminator G3 is s heavy duty quality machine. The discs worked extremely well and planting and culti-packing is very smooth and easy. Working with Dillon at Ripping It Outdoors was a very good experience and seamless transaction.
After spending way to much money for forest mulching services I discovered this wonderful machine. It's not a giant powerhouse forest mulcher, but it does everything a property owner needs to maintain a forested property. I wish I would have found it sooner.
The Firminator is well built and functions well. I am having some trouble while planting mixed size seeds. Next time out I’ll try setting it so only the smaller seeds drop out the open it up for the larger seeds.
easy buying process and great communication. Mulcher works great, easily clears overgrown brush and even mulched a 5" thick mulberry tree fairly easily. running it off of my old 331 bobcat with no problem powering the drum at all. Only small issue which isn't a big deal is that the supplied hoses are about 16" too short to operate a full range of motion.
Over all built well. I like it is all cast iron and metal and not plastic. Had to modify fertilizer disc mount to fit correctly, nothing major, a little grinding. I modified the center link hitch point to accommodate my John Deere quick hitch. Have yet to plant with it but I’m sure it will work perfect. Love the grease fittings everywhere. Reminds me of the old farm equipment I grew up on, and still use periodically.
My firminator RT was delivered in good condition in ND. I will be using it next week. I have a 45 HP John Deere tractor that is supposed to lift 2000 lb but really struggles to lift this 6 foot firminator RT. I will just have to use in as a two pass operation for now.
I do wish there was a better operating manual for this unit. Maybe that is something you can work on.
I will give you an update once I start using it in a few days.
Great piece of equipment. Performs far better than I expected. One piece of advice - if property is significantly overgrown, consider the tractor attachment first to bring down the over growth and then switch to the UTV attachment to maintain property. No complaints worked perfectly.
Put this on Kubota 900 with winch hookup. This thing is a beast (within reason). I named it ‘Homie”, cause Homie don’t play. It will take care of stuff up to about 2” in diameter. You still have to remember that this is NOT like the ones on a bobcat or larger machinery. It does have its limits. But all in all I am very satisfied with it. Now on to the good part! The staff at Ripping It are outstanding! Especially Kayla in the office. She has gone above and beyond on making sure everything went right, from ordering to questions about installation. This young lady would be of great value at ANY company ! Her knowledge and personality are like over the top. This is my first experience with Ripping It Outdoors and I can only say positive things about them. With all that being said, I do fill out reviews on things I buy, AND I give a honest review. If it’s bad then you will know it. But if it’s good, well I tell the truth ! Again Kayla, from the bottom of my heart, a great big THANK YOU for all your help and just talking to you. I feel like we’ve know each other for years!
TENT is easy to put up , material is tuff as told....only complaint is that i wish the bottom had about 3 to 4 inches overlap towards the inside so i could install a 2 x4 or something to help hold the tent down in high winds we have here in virginia thanks
Hi, my name is Ken. I’ve had a great experience with Ripping It Outdoors. I purchased a Forax Hp40 Mulcher for my mini excavator. Kayla Patterson is who I dealt with from the beginning until I received it at my house. She has been wonderful to work with and looking forward to working with her with any other orders I purchase. Kayla answered any questions I had and kept me updated throughout the whole process, can’t say it enough just a wonderful person to work with!!
These are great feeders if you don’t have any feral hogs but if the hogs tear off the wiring harness from the timer to the feeder motor, you’re disabled. Then, if you ask for help from Outback, they refer you to the dealer but really you’re on your own for parts and repairs.
I have three Outback feeders that work as designed. They’re 13 years old and have always served well but this feeder misses the mark by a very high margin. I’d NEVER buy this product again.
Feeders need to be dependable and this unit is not.
This is my first experience with Ripping It Outdoors. Fortunately I got Dillion as a representative and everything from sales to shipping was spot on..
Thanks Dillion for your help!!
The only thing is when hooking up the actuator on my ATV. The wire is long going to the plug in. What has happened in the past about this. Is their video showing the usage of the control?