The Autotransformer: for step up, step down and split phase balancing An autotransformer can be used for step up, step down and split phase output balancing purposes. While the step up and step down functions are fairly straightforward, split phase output balancing may require some more attention.
Consider for example a 30A 120/240V split phase supply. The supply could be the grid, a generator or two stacked inverters. Some of the loads connected are 240V, others are 120V. On each 120V leg the load should not exceed 30A. The problem is that as soon as 120V loads are connected, the two legs will show a different current. This is because the 120V loads on the two legs will never be balanced. A 120V 1200W hairdryer, for example, will draw 10A from one leg. A 120V washing machine could even draw in excess of 20A from one leg. Between the two legs the difference in current, or current unbalance, will therefore often be 20A or more. This means that the 30A supply will not be used up to its full potential. By the time one leg draws 30A, the other leg may be drawing no more than 10A, and increasing the 240V load, for example, will result in an overload of one leg while the other leg still has spare capacity. Theoretically, the total power that can be drawn from a 30A 120/240V supply is 30 x 240 = 7,2 kVA. In case of 20A unbalance, the practical maximum will be 30 x 120 + 10 x120 = 4,8kVA, or 67% of the theoretical maximum. The solution is an Autotransformer. By leaving the neutral of the split phase supply unused, and connecting an Autotransformer to create a new neutral, as shown in figure 1, any load unbalance is ‘absorbed’ by the Autotransformer. In case of a 30A supply, the load can be increased to 7,2kVA, and a 20A load unbalance will result in one leg supplying 40A, and the other leg 20A. The 20A difference will flow through the neutral and the windings of the Autotransformer. The current through both 120V wires of the split phase supply will be 30A.
Temperature protected In case of overheating, the Autotransformer is disconnected from the supply. Reset is manual. Ground relay for use with Multi or Quattro Inverter/Chargers included When operating in inverter mode, the neutral output of the inverter/charger must be connected to ground to guarantee proper functioning of a GFCI. In case of a split phase supply the neutral must be grounded. For this purpose a grounding relay is built in the autotransformer’s enclosure. The relay is controlled by the 230/240V Multi or Quattro. (The internal grounding relay in the 230/240V Multi or Quattro must be disabled)
An alternative to stacked inverters The alternative to stacking two 120V inverters to provide a 120/240V split phase supply is a 240V inverter with an additional Autotransformer.
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
Please contact your dealer for any returns, repairs or support issues related to this product.
I've started using the mulcher I on several parcels of land 10 acres . I have grind down a couple of 14 inch stumps. Caution the mount bracket behind the mulcher motor exhaust gets extremely hot even with gloves on . But the unit so far seems to works very good it's well put together.
The Firminator G3 is s heavy duty quality machine. The discs worked extremely well and planting and culti-packing is very smooth and easy. Working with Dillon at Ripping It Outdoors was a very good experience and seamless transaction.
The week before leaving for my mule deer hunt in Wyoming, I seeded the area surrounding the new runway at Wertheimer Airport in Norman.
This past Tuesday, I returned to finish the job and was pleased to see that the seed I planted just two weeks earlier was already germinating and coming up nicely.
These pictures show the freshly seeded areas alongside those planted two weeks ago. It’s a great comparison and a good example of what proper seedbed preparation and planting can accomplish.
I used my Ferminator G-3, which is one impressive piece of equipment. It prepares the seedbed, plants the seed, smooths the soil, and firms everything up for good seed-to-soil contact—all in one efficient operation.
I’ve owned and operated several no-till drills over the years, but I can say without hesitation that the Ferminator is the most efficient and versatile seeding machine I’ve ever owned.
There’s something pretty satisfying about returning to a job and seeing those first green shoots coming through the ground. That’s when you know your hard work is paying off!
Just got my Buffalo Turbine! Love it. Took a little bit to get used to getting the right angle for the nozzle, but not a problem. Side note, works much better if the frame is level as much as possible.
Love it!
Gary Haddock
Seems to be in order delivery wasn't able to use lift gate but tractor was able to take pallet off the truck bed. No damage to machine after visual check. won't know how it runs until rain stops.
Staff at RippingitOutdoors was very quick to call and double check the type of backet needed for the unit to ensure the online order matched( to fit my skid steer quick attachment on my l2501 Kubota). Explained the teeth & belt could be ordered through them directly over the phone when/if needed as well as selling other types of custom made brackets for Utv's ect. All around Great customer service and would purchase from again.
After spending way to much money for forest mulching services I discovered this wonderful machine. It's not a giant powerhouse forest mulcher, but it does everything a property owner needs to maintain a forested property. I wish I would have found it sooner.
The Firminator is well built and functions well. I am having some trouble while planting mixed size seeds. Next time out I’ll try setting it so only the smaller seeds drop out the open it up for the larger seeds.
easy buying process and great communication. Mulcher works great, easily clears overgrown brush and even mulched a 5" thick mulberry tree fairly easily. running it off of my old 331 bobcat with no problem powering the drum at all. Only small issue which isn't a big deal is that the supplied hoses are about 16" too short to operate a full range of motion.
Over all built well. I like it is all cast iron and metal and not plastic. Had to modify fertilizer disc mount to fit correctly, nothing major, a little grinding. I modified the center link hitch point to accommodate my John Deere quick hitch. Have yet to plant with it but I’m sure it will work perfect. Love the grease fittings everywhere. Reminds me of the old farm equipment I grew up on, and still use periodically.
My firminator RT was delivered in good condition in ND. I will be using it next week. I have a 45 HP John Deere tractor that is supposed to lift 2000 lb but really struggles to lift this 6 foot firminator RT. I will just have to use in as a two pass operation for now.
I do wish there was a better operating manual for this unit. Maybe that is something you can work on.
I will give you an update once I start using it in a few days.
Great piece of equipment. Performs far better than I expected. One piece of advice - if property is significantly overgrown, consider the tractor attachment first to bring down the over growth and then switch to the UTV attachment to maintain property. No complaints worked perfectly.
Very pleased. Product was better than anticipated and is working well.
I expect the 2000lb feeders to last at least a decade based on my use with cattle.
If feeding wild game would likely last a lifetime with minimal maintenance.
seeds come out way to fast at lowest setting when planting alfalfa literally the only reason I bought it now I can't even use it and I can't return it so I'm stuck with it for the price you pay you would think it would work!
It’s built solid. It handles Field grass hip high pretty well. With the maintaining the field grass after the first cut, the pasture field is starting to look like a lawn. The 84 inch with the best thing to get for 8 acres. It’s best to order belts for back up in the event if the belts were to break. But overall, I like the product quality is good.
When I think of ripping it outdoors something else comes to mind, but I digress. This spreader is awesome. Works like a champ. The hopper is big enough to do my 1 acre lot for my applications. Just load once and go. I would highly recommend this spreader. It saves a ton of time and is a quality product.